Pyle® PLAM3000 - Academy Series Class AB 4-Channel 3000W Amplifier

Pyle® PLAM3000 - Academy Series Class AB 4-Channel 3000W Amplifier
$ 117
In stock: 22 pcs.
Product Detail:

RMS Power Rating 4 Ohms: 750W x 4 channels
RMS Power Rating 2 Ohms: 1000W x 4 channels
RMS Power Rating 4 Ohms, Bridged: 200W x 2 channels
Max power output: 3000W
Signal/Noise Ratio: 90dB
Variable Bass Boost: (0 to +12 dB bass boost at 50Hz)
Variable high-pass filter: (120-3000Hz, 24 dB/octave)
Variable low-pass filter: (50-250Hz, 24 dB/octave)
Subsonic filter: (24 dB at 15Hz)
Bass EQ 6dB / 12dB @ 45Hz
Speaker Impedance 2-16 Ohms
Fuse Size 2 x 30A
Frequency response: 15Hz-30kHz
Dimensions: 9-7/10"W x 14-1/10"L x 2-2/10"H


  • Pulse Width Modulated MOSFET power supply
  • Wired remote bass level control included
  • LED power (green) and protect (red) indicators
  • Soft start turn-on
  • 4/3/2 Channels operation
  • Preamp RCA outputs to daisy chain multiple amps
  • 3-way protection circuitry (thermal, overload, and speaker short protection)
  • Heavy duty aluminum alloy heat-sink for extreme heat dissipation
  • Nickel-plated RCA level inputs
  • Nickel-plated screw terminals
  • 4 gauge power and ground wiring is required for installation.

Versatile Hybrid Amplifiers:

The Pyle Academy Series Amplifiers will provide your audio setup with sophisticated new sound and serious power. Add performance and quality enhancement to your music when you upgrade your audio system with these rugged and high-efficiency amps. Enjoy tomorrow’s advanced sound technology that outperforms all other amps in its class.

This lineup of Pyle Academy amps will educate your audience with the knowledge of true sound quality. These amps will give you that sound you’ve been looking for with crisp music reproduction in the mobile environment.

Sound Specialization:

These high-efficiency class-D amplifiers host an impressive power output and are where form and function meet. Configurable for Bridgeable and Tri-Way applications, built-in Variable Subwoofer Crossovers, MOSFET Pulse Width Modulated Power Supply, High Level Low Impedance MOLEX Input Connector, strong frequency response rates along with plenty of more features that make the Pyle Academy Series Amplifiers smarter than the competition.

Intelligent Design:

Safety features include power and protection LED indicators; soft turn-on/off, thermal, overload and speaker-short protection. The built-in air-induction fan cooling system acts as another line of safety keeping you and your equipment safe. Status LED Diagnostic Condition indicators show when the amplifier is powered up normally and when your system is experiencing a protection fault.

Pump it Up:

Take advantage of the Bass EQ Boost and turn it up. Make adjustments to the Bass EQ settings until you achieve that extra amount of kick you’ve been waiting for.

Intelligent Sound – Intelligent Style:

The smooth-edged and rounded design leaves a blue-pearl gloss finish on the fortified aluminum heat-sink. The stream-lined and high-tech appearance will definitely add some attention to your audio.

Total Audio Control:

Once you’re connected, customize and adjust your listening experience to your liking with the amplifier’s control center. You can personalize and fine-tune settings like:

  • High-Pass Filter– When Crossover Mode is in High-Pass Mode, this control limits the frequencies which will be distributed to the speakers Crossover Switch – Routes output of the Low Pass (LP), or the output of the High Pass (HP) filters, or ‘FULL’ to the internal power amplifier.
  • Low-Pass Filter - When Crossover Mode Selector is in Low-Pass Mode, this control limits the frequencies which will be distributed to the speakers.
  • Line Input – Accepts line level (RCA) inputs from 0.2 to 5-Volt.
  • High-in - Accepts speaker level inputs from radios that do not line level (RCA) outputs.
  • Bass EQ - Variable from a range of decibel adjustments, this feature regulates the impact of your bass kick. You’ll have manual control over balancing and correcting the frequency range of a given sound.

Speaker Output Connections:

Connect right and left speaker wire to corresponding speaker output terminals of the terminals. Be sure to have the positive wire from the speaker to the positive speaker terminal of the amplifier and the negative wire from the speaker must connect with the speaker terminal of the amplifier. Reversing any of these connections will result in the speaker cones moving out of phase which causes bass cancellation.

Input Connections:

Turn the volume control on the amplifier to minimum initially. Once the initial power sequence has been performed, set the volume control to roughly 80% of full power. Play some audio and slowly turn up the amplifier volume control until you hear some distortion, and then back it off for the sharpest sound setting. This amplifier has RCA connections for Low Level inputs. Low Level signal is carried through RCA cables. It is preferred to use Low Level inputs to the amplifier if the headunit is equipped with matching outputs.

This part is universal

Delivery Information:

FAST and FREE Delivery in Toronto. Delivery time: up to 24 hours. Order by 2pm for Delivery Today.

FREE Delivery in Canada. Delivery time: 24-48 hours. Order by 3pm for Next Day Delivery.

FREE International Delivery Available. Delivery time: 2-6 working days.

Main Categories

Automotive Chemicals

Car Audio & Electronics - (You are here)

Car Exterior

Car Interior

Car Lighting


Work Time

Accepting orders & Shipping
9:00 am - 18:00 pm (Mo, Tu, We, Th, Fr)
9:00 am - 14:00 pm (Sa)
Su - off-time


Delivery in Toronto

  • Courier to the address
  • Free shipping

Shipping in Canada

  • UPS
  • DHL
  • Cash on delivery
  • Visa
  • MaestroCard
  • MasterCard
  • Paypal
  • Cash
payment visacard payment maestrocard payment mastercard payment paypal
back to top